A DIY ELECTRONIC LOAD FOR DC-DC CONVERTER CHARACTERIZATION

Summary of A DIY ELECTRONIC LOAD FOR DC-DC CONVERTER CHARACTERIZATION


This article describes a DIY electronic load designed for DC-DC converter characterization, featuring an ATmega328P microcontroller and precise measurement capabilities. The project enables constant current, power, and resistance modes with real-time efficiency logging and temperature-controlled fan management.

Parts used in the DIY Electronic Load:

  • Atmel ATmega328P AVR microcontroller
  • MCP47FEB21A1 I2C 12bit DAC
  • LTC2992 dual power monitor chip
  • MCP2221A USB serial interface bridge
  • 16×2 LCD display
  • 10mΩ shunt resistor
  • 0.2Ω shunt resistor
  • W9NK90Z N-ch power MOSFETs (two units)
  • Heatsink salvaged from an old graphics card
  • 10k NTC thermistor
  • Generic 12v @ 200mA 80mm fan
  • MCP6H02 opamp
  • User-definable bi-color status LEDs
  • Rotary encoder
  • Load ON/OFF button

A project by reivax-boucoi:

The heart of the system is an Atmel ATmega328P AVR microcontroller with 32kB of Flash and 2k of RAM running at a whopping 16MHz. It interfaces an I2C 12bit DAC (the MCP47FEB21A1) and the LTC2992 dual power monitor chip.

A DIY ELECTRONIC LOAD FOR DC DC CONVERTER CHARACTERIZATION

The USB serial interface uses the MCP2221A bridge. The display is a classic 16×2 LCD.

On the analog part, 10mΩ and 0.2Ω shunt resistors are used, coupled with two W9NK90Z N-ch power MOSFETS. The heatsink was salvaged from an old graphics card. Attached are a 10k NTC and a generic fan (12v @ 200mA, 80mm). Current regulation is achieved through the help of a MCP6H02 opamp, and a carefully designed feedback network which guarantees the specified rise time with little to no overshoot.

The layout was done using the Eagle software (v9.5.2). Gerbers, Eagle project files, top and bottom views are available on the pcb folder. PCBs were printed using JLCPCB service. The schematic is available in a pdf and Eagle .sch format as well.

Several user-definable bi-color status LEDs are included, such as Load ON/OFF, TX & RX, acquisition blink, as well as a power LED.

An expansion/debug port is provided, with +5V, ground, I2C and UART available.

There are several issues regarding the layout of the PCB, as it is a first version. Improper Kelvin connections to the current sense resistors, or wrong hole size for the power input connector by example. The heatsink originally used is salvaged from old equipement and the footprint may not be relevant to anyone else. Space for rubber feet placement should be included. Also, the LCD is too close to the heatsink, which is impractical during assembly (especially accessing the fan and temp sensor connector).

Features

  • Constant Current, Power and Resistance modes
  • Battery capacity logging with adjustable cutoff voltage
  • Input and output power logging : instant efficiency reading for DC-DC converters
  • Rotary encoder driven interface
  • Dedicated Load ON/OFF button
  • Intuitive LCD menu system with editable values
  • 12bit current, voltage and power measurements
  • 30W continuous sinking capability, 250W peak
  • Temperature controlled fan with auto shutdown.
  • Adjustable acquistion rate
  • 115200 bauds serial communication through USB with a PC (non-isolated !)

Read more: A DIY ELECTRONIC LOAD FOR DC-DC CONVERTER CHARACTERIZATION

Quick Solutions to Questions related to DIY Electronic Load:

  • What is the heart of the system?
    The system uses an Atmel ATmega328P AVR microcontroller running at 16MHz.
  • How is the USB serial interface implemented?
    It uses the MCP2221A bridge for connectivity.
  • Which components are used for current regulation?
    Current regulation is achieved using an MCP6H02 opamp and a carefully designed feedback network.
  • What software was used for the PCB layout?
    The layout was done using Eagle software version 9.5.2.
  • Can the device measure instant efficiency?
    Yes, it provides input and output power logging for instant efficiency reading of DC-DC converters.
  • What are the power handling capabilities?
    The device offers 30W continuous sinking capability and 250W peak power.
  • Is the serial communication isolated?
    No, the 115200 bauds serial communication through USB with a PC is non-isolated.
  • What issues were found in the first version layout?
    Issues include improper Kelvin connections, wrong hole sizes for the power input connector, and the LCD being too close to the heatsink.

About The Author

Author avatar

Muhammad Bilal

I am a highly skilled and motivated individual with a Master's degree in Computer Science. I have extensive experience in technical writing and a deep understanding of SEO practices.

Stay in the loop

New AVR projects, tutorials and schematics, every week.

Subscribe Browse projects

Scroll to Top