A 128 x 64 graphic LCD is in the clear plastic box at the top. It is connected to the waveform capture and control unit in the green pencil box below the display. Downloads AVR Studio 3.5 ASSEMBLY SOURCE for the waveform capture controller. AVR Studio 3.5 ASSEMBLY SOURCE for the control panel and LED […]
Minimum Mass Waveform Capture and Display using AT90S2313 microcontroller Read More »
Downloads Download the Download FreePC files in and the detector board layout png file in zipped forma: schottkydedtector080309 Find updates at www.projects.cappels.org Starting to do a little work at 330 MHz, I decided that my existing field strength meters were not adequate for for my needs. The 330 MHz project came to a stop, and
A Field Strength Meter Using A Biased Schottky Detector using microcontroller Read More »
This is a handy companion for a digital voltmeter. Its allowed me to do a lot of things I used to use my oscilloscope for, and in addition it measures voltages to much greater precision.Using an LM324 quad op amp, this peak detector provides 2% measurement accuracy on square waves from 5 Hz to 20
Precision Audio Frequency Peak Detecting Probe using microcontroller Read More »
Encased in a pencil box to keep the point-to-point wiring on the back of the board from shorting to wires and things on the workbench, the plastic case also holds the offset and gain post as well as the input connector and the switches that switch on the near-zero and near-full scale references. I wanted
HF AC Millivoltmeter Adapter using microcontroller Read More »
About This project describes an open software open hardware pH meter using an Arduino/Freeduino board. In other words, this is an electronic circuit to be connected with a glass electrode pH sensor. It was possible by the idea from my friend Mr. Denis Vidal, the space that my supervisor gave me, prof. Dr. Emanuel Carrilho,
PHduino pH Meter Using Arduino Read More »
A milliohmmeter is just the tool for checking trace resistance on a printed circuit board, tracking down shorted traces, and measuring the contact resistance of a switch or connector. Its the kind of tool that would come in real handy occasionally, but not often enough to justify shelling out hundreds of dollars. Wanting one anyway,
A Microcontroller Based Digital Lock-In Milliohmmeter using ATtiny2313 microcontroller Read More »
Specifications Input: AC, DC or AC+ DC to > 10 KHz Ranges: 200 mv, 2V, 20V, 200V, 600V full scale Accuracy: ±1%, depending on divider resistor selection Crest Factor: 1 to 3, up to 5 with degraded accuracy Input impedance: 1 Megohm shunted by 20 pf Battery drain < 300 uA Introduction The DVMs in
TRUE RMS-TO-DC Adapter For DVM using microcontroller Read More »
Briefly, • AC True Watts using two quadrant multiplier • Optimized for 120 VAC (can be changed) • 15 watt full scale (can be changed) • Uses DVM floating on AC Neutral as display • Requires moderately high level of analog circuit skill • Very inexpensive Find updates at: www.projects.cappels.org Introduction I am doing some
A Pretty Good Wattmeter For Bench Use using microcontroller Read More »
Simplicity in circuitry was the design direction. Zero mass (firmware only with no physical components) would the ultimate achievement. This instrument doesn’t have any front panel controls because the user interacts via an RS-232 terminal program at 9600 baud. I needed a frequency meter for my experiments in Nondu, Thailand, where I really don’t have
RS-232 Freq. Meter/Pulse Generator Based on Atmel ATtiny2313 using microcontroller Read More »
Overview After finishing Little More Serious Frequency Meter I had planned to make a suitable preamp and prescaler for it, and set about to gather ideas and parts. I was inspired by one fellow who had built the meter and the 2 line X16 character LCD display to show the output, succeeded in designing a
