Comments: All resistors are 1/4W.The circuit is powered by 9…15V DC or AC. When In Circuit Programming (ISP) connectors are used, is possible the programmer to be powered from targets power source. Diodes D2 and D6 protect the regulator LM7805, when targets power is used. ‘ XTAL JUMP ‘ is used to cut XTAL when […]
Ponyprog Circuit for AVR & PIC16F84 using microcontroller Read More »
The ATMEL AVR programmer works with the Windows program “Ponyprog” which works under 95, 98, XP. On board the AVRs that can be programmed are those in the schematic. For other members of AVR family or the rest programmable ICs that Ponyprog can program, there is the J1 connector (CON10) which allows expanding the programmer’s
Ponyprog Circuit for ATMEL’S AVR using microcontroller Read More »
Devices The EEprom programmer software supports the following devices. 28C16 28C256 28C17 29C256 28C64. Hardware Diode D1 and resistor R1 provide the VDD isolation when programming the 24 pin devices. The jumper J3 must be shorted for 24 pin devices, and open circuit for 28 pin device programming. For more detail: EPROM adapter for ATMEL
EPROM adapter for ATMEL 89 Series Flash Microcontroller Programmer Read More »
Tired of spending hours and hours in wire soldering? Do your circuits look ugly and you are looking for a way to produce professional-like PCBs? Then you had better try photoetching. And the first step to do that is to have the right equipment that is an Automated Exposure Box. Moreover if you like tinkering
PCB Exposure Box with Countdown timer using ATMEGA8 microcontroller Read More »
Introduction of 89Sxx There are some 89Sxx development board, here is another one. I have designed this single side development board to be used as a tool for learning MCS-51 Microcontrollers, and for easy microcontroller project development. The 89Sxx development board features : 89Sxx 40-DIL based design, 89S51/52/53 In System Programming (ISP) through the 6-pin header
89Sxx Development Board using microcontroller Read More »
This is a Minimum Mass Wireless Coupler that connects a terminal, or PC running terminal software, to other Minimum Masss Wireless devices by means of a 1200 baud data channel at 181.818 kHz. The basic Minimum Mass Wireless Coupler technology is described and links to other projects on this site that use the Minimum Mass
Wireless Coupler Terminal Interface using AVR microcontroller Read More »
The hot melt glue that covers the circuit serves multiple purposes: It helps to keep the temperature even among the three transistors (to minimize thermal drift), it protects the components from physical damage, and it holds the battery holder on the board. As I used this probe last nigh to determine if a 384 MHz
RF Field Strength meter using AVR microcontroller Read More »
The ATmega8 microcontroller-based Low-Cost Telemetry Device (LTD) is an efficient telemetry keyer. The LTD measures the voltage levels of up to four analog channels via its on-chip 10-bit ADC, converts the measurements to numbers, and then sends the data in Morse code to an external transmitter and to an attached RS-232 terminal. It can be
Digital Telemetry using ATMega8 microcontroller Read More »
A well known L/C measurement circuit is pressed into service to make a bare bones measurement circuit. Download the AVRStudio assembly source: lgm031227I.asm Download the AVRStudio hex file: lgm031227.hex Left-to-right: The 5 volt regulator, the LM393 oscillator (a 0.047 uf capacitor is mounted on the LC circuit connector), the AT90S2313, and the serial connector to
LC Resonant Frequency Meter using AVR microcontroller Read More »
Useful as a transmitter tune-up meter or an RF sniffer, this is an RF field strength indicator that is loosely based on the Broad Band RF Field Strength Probe, described elsewhere. It detects RF via a square law detector, basically its a crystal set with gain. For more detail: AVR LED RF Field Strength using
AVR LED RF Field Strength using microcontroller Read More »
